当前位置:首页>> >>


四辊卷板机设计(有cad图 文献翻译).rar

收藏

资源目录
    文档预览:
    编号:20181016173631226    类型:共享资源    大小:2.16MB    格式:RAR    上传时间:2018-10-16
    尺寸:148x200像素    分辨率:72dpi   颜色:RGB    工具:   
    19
    金币
    关 键 词:
    四辊卷 板机 设计 cad 图文 翻译
    资源描述:
    河南理工大学万方科技学院本科毕业论文1附录:外文资料和中文翻译外文资料:Testing of Tool Life CostMachining cost is the sum of the machine tool cost and the cutter cost. The machine cost consists of idle cost, machining cost, and tool changing cost. The machining cost decreases with increased cutting speed; while the idle cost remains constant with changes in cutting speed. From the machining data handbook [24] the generalized machining cost equation is listed below: 13.)1(82.3.82.3 321  pCbPrrdir GtKtvTfDLvfttRvfeLDMCIn order to optimize the cutting condition, it is essential to determine the mathematical relationship between the cuttings inserts type and cutting speed. In our study Taylor's model will be used in relating the cutting tool life to the cutting speed:VT“ =C ....................................V= cutting speedT= Cutting time to produce a standard amount of flank wear (e.g. 0.2mm) n and C are constants for the material or conditions used.In order to determine constants `n' and `C' for the cutting inserts under study in machining 4140 steel and the conditions used in the experiments, a 河南理工大学万方科技学院本科毕业论文2LogV against LogT is drawn and shown for the three types of cutting inserts under study Figure 1, Figure 2are for KC313 under dry and wet conditions, Figure 3, and Figure 4are for KC732. In addition, Figure 6, and Figure 7are for KC5010. It can be seen from the aforementioned figures that in-spite of considerable scatter in test measurements, the results fall reasonably well on a straight line. From the curves it can be seen that for the same cutting speed the tool life increases by increasing the wear criterion and introduction of coolant emulsion for KC313 and KC732. However, as seen in KC5010 tool life increases by increasing the wear criterion and decreases by introducing coolant. This negative behavior of KC5010 toward coolant emulsion and the effect of wear mechanisms behind it will be covered in Chapter 5. As well as the wear kinds on other inserts investigated in this research.Metal cutting studies focused on tools' wear, tool life, and wear mechanisms. However, future research should pay more attention to other factors as well: Wear criterion value set up by the factory system, which basically the tool wear threshold value that suits the factory product. Types of tools used, such as carbide tips and high speed tools. Studying the variation of tool life wear under dry and wet cutting that effect the tool life equation constants (C,n) is useful. This will improve tool life because it also affects the economy of cutting [24].河南理工大学万方科技学院本科毕业论文3In order to determine the effect of cutting fluid on the selected wear criterion, relationship between different wear criteria and machining cost for the cutting inserts under HSM must be studied. The value of the tool life constants (C,n) for different wear criteria are extracted and plotted within the ranges listed in table (1). The values of the constants (C, n) extracted from Figure 1/B, Figure 3IB, and Figure 3-10 are shown in tables1 and 2. Further explanation of the relationship between these parameters and wear criteria will be covered through out the next figures. Figure5represents the relationship between `n' and wear criterion. As wear criterion increase `n'.河南理工大学万方科技学院本科毕业论文4(a) Log (time) versus Log (speed) at different wear criteria (dry condition).(b) Log (time) versus Log (speed) at different wear criteria (wet condition)Figure 2Time versus speed at different wear criteria KC313. (a) Log (time) versus Log (speed) at different wear criteri(drycondition). (b) Log (time) versus Log (speed) at different wear criteria (wet condition).河南理工大学万方科技学院本科毕业论文5(a)Log (time) versus Log (speed) at different wear criteria (dry condition)(b) Log (time) versus Log (speed) at different wear criteria (wet condition).Figure 3Time versus speed at different wear criteria KC732 (a)Log (time) versus Log(speed) at different wear criteria (dry condition), (b) Log (time) versus Log (speed) at different wear criteria (wet condition)(a)Log (time) versus Log (speed) at different wear criteria (dry condition).河南理工大学万方科技学院本科毕业论文6(b)Log (time) versus Log (speed) at different wear criteria (wet condition)Figure 3-10 Time versus speed at different wear criteria KC5010 (a) Log (time) versus Log(speed) at different wear criteria (dry condition), (b) Log (time) versus Log (speed) at different wear criteria (wet condition).Table 1 Ranges of plotted tool life constants.Range Cutting Insert Condition0 < LogT< 2.6 KC313 Dry0< Log T< 4.1 KC313 Wet0
    展开阅读全文
    1
      金牌文库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。
    0条评论

    还可以输入200字符

    暂无评论,赶快抢占沙发吧。

    关于本文
    本文标题:四辊卷板机设计(有cad图 文献翻译).rar
    链接地址:http://www.gold-doc.com/p-228763.html
    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服客服 - 联系我们
    copyright@ 2014-2018 金牌文库网站版权所有
    经营许可证编号:浙ICP备15046084号-3
    收起
    展开